MotorCodex Español

P0122 — Throttle Position Sensor (TPS) — Circuit Low Input

Moderate

Quick answer

P0122 means the throttle position sensor’s the signal is stuck low — typically a short to ground, an open signal wire, or a dead sensor. Symptoms feel mechanical: hesitation, surging, harsh shifts, a dead pedal moment. On drive-by-wire engines the computer responds to TPS faults with limp mode (reduced power) as a safety measure. Check the connector and wiring before buying a sensor — for this variant of the code, wiring is the most common answer.

What it means

The throttle position sensor (tps) tells the engine computer exactly how far the throttle is open — the computer’s read on what your right foot is asking for. P0122 sets when the signal is stuck low — typically a short to ground, an open signal wire, or a dead sensor for long enough that the computer stops trusting it.

Circuit codes describe electrical behavior, which puts the wiring, the connector, and the sensor on equal footing as suspects. The cheapest of the three fails most often.

While the signal is untrusted, the computer substitutes a safe default value. The engine runs, but on assumptions instead of measurements — that’s the drivability change you feel.

P0122 symptoms: what you'll notice

  • Hesitation or a dead-pedal moment when you press the gas — the engine pauses before it responds.
  • Surging or uneven power while holding a steady speed on the highway.
  • Harsh or oddly timed transmission shifts.
  • Sudden reduced power (limp mode) on drive-by-wire engines, often with a wrench or reduced-power warning light.
  • An idle that races or hunts up and down.

Common causes

Ordered from most to least likely.

  1. 1.

    Wiring damage (chafe, break, melted insulation)

    A short to ground pins the signal low.

  2. 2.

    Corroded, loose, or backed-out connector pins

    Unplug and inspect both halves under good light.

  3. 3.

    Failed throttle position sensor

    Confirm with measurements before replacing.

  4. 4.

    Worn potentiometer track (older TPS)

    Creates a flat spot/glitch at the most-used pedal position.

  5. 5.

    Lost 5V reference or sensor ground (where applicable)

    If several sensors fault together, suspect a shared reference circuit rather than coincidence.

How to fix it: diagnosis, step by step

Cheapest and most likely checks first.

  1. 1 Read the freeze frame

    Note when P0122 sets — cold start, warm idle, under load, over bumps. The conditions narrow the cause dramatically, especially for intermittent faults.

  2. 2 Inspect connector and harness

    Unplug the sensor; check for corrosion, bent or spread pins, and chafed insulation along the harness run. Re-seat firmly. This free step resolves a remarkable share of circuit codes.

  3. 3 Watch it in live data

    Watch TPS percentage while sweeping the pedal slowly: it should rise perfectly smoothly from ~0 to ~100% with no dropouts, spikes, or flat spots.

  4. 4 Do the slow-sweep test

    Key on, engine off, scanner live: sweep the throttle slowly and watch for any glitch in the percentage. Older potentiometer-style sensors wear a dead spot exactly where the throttle sits at cruise.

  5. 5 Wiggle-test if intermittent

    Engine running, data live: gently flex the harness and tap the sensor while watching the reading. A glitch you can provoke is a fault you can find.

  6. 6 Replace with a quality part

    If measurements condemn the sensor, buy OEM or a reputable brand — bargain sensors re-set these codes often enough to cost more in time than they save in money.

Parts & tools you may need

Disclosure: some links are affiliate links (including the Amazon Associates program). If you buy through them, we may earn a commission at no extra cost to you.

Related codes

Frequently asked questions

What does code P0122 mean?
P0122 means the throttle position sensor’s the signal is stuck low — typically a short to ground, an open signal wire, or a dead sensor. It’s moderately serious — you can usually keep driving gently, but diagnose it soon.
Can I drive with P0122?
With caution. If the vehicle enters limp mode, that’s the system protecting you — get it diagnosed promptly rather than driving around it.
Is it the sensor or the wiring?
For this variant, lean wiring: stuck-low, stuck-high, and intermittent signatures are circuit behaviors. Inspect and measure before buying the sensor.
Why did the code return after a new sensor?
Because the circuit, not the sensor, was the fault — or the replacement was low quality. Re-do the wiring inspection the first repair skipped.
What does the computer do meanwhile?
It substitutes a default value and keeps the engine running on assumptions. Functional, but you pay in drivability and fuel until the real measurement comes back.
Ask Codi