MotorCodex Español

P0706 — Transmission Range Sensor Range/Performance

Moderate

Quick answer

P0706 means the PRNDL sensor's signal exists but doesn't match reality or changes implausibly. Typical symptoms: wrong gear shown on the dash, start-in-gear oddities, intermittent no-crank. Before anything else: check sensor adjustment and linkage first — a misadjusted range sensor mimics every electrical failure it has.

What it means

Automatic transmissions are controlled hydraulically but supervised electronically: sensors report shaft speeds, temperature, and gear position, and solenoids convert the computer’s decisions into fluid pressure. P0706 reports that the PRNDL sensor's signal exists but doesn't match reality or changes implausibly.

The golden rule of transmission codes: check the fluid before believing any other theory. Level, color (should be red/pink, not brown), and smell (burnt = bad news) — degraded fluid causes shifting complaints, solenoid misbehavior, and ratio errors that perfectly imitate failed parts.

P0700 usually accompanies this code; it’s just the pointer that tells the engine computer to turn on the light. Diagnose the specific code, not P0700.

P0706 symptoms: what you'll notice

  • The dash shows a different gear than where the lever actually is
  • Intermittent no-crank in Park — wiggle the lever and it suddenly starts
  • The engine starts in positions it shouldn’t, or refuses to start in Neutral
  • Harsh or delayed engagement, sometimes limp mode
  • Reverse lights acting up

Common causes

Ordered from most to least likely.

  1. 1.

    Low, degraded, or wrong-spec transmission fluid

    Always first. The fluid specification matters as much as the level.

  2. 2.

    Failed sensor or solenoid (per the specific code)

    Most test with a simple resistance measurement at the case connector.

  3. 3.

    Wiring or connector damage at the transmission

    The case connector lives in heat and spray; corroded pins are common.

  4. 4.

    Internal wear (clutches, valve body)

    The expensive story — earn it by ruling out the cheap ones first.

How to fix it: diagnosis, step by step

Cheapest and most likely checks first.

  1. 1 Check the fluid first

    Level per your vehicle’s procedure (dipstick or level-check plug), color on a white towel, and smell. Burnt or brown fluid reframes the whole diagnosis; low fluid plus a leak explains half of these codes.

  2. 2 Read all transmission codes

    Use a scanner that addresses the transmission module. The combination of codes (one solenoid vs. several, sensor + ratio together) localizes the fault.

  3. 3 Check sensor adjustment and linkage first — a misadjusted range sensor mimics every electrical failure it has

    This is the code-specific first move — do it before parts shopping.

  4. 4 Test electrically at the case connector

    Most transmission sensors and solenoids can be resistance-tested from the external connector with a wiring diagram, no disassembly needed.

  5. 5 Decide: pan-level repair or specialist

    Fluid, external sensors, and many solenoids are DIY-reachable. Valve body and internal clutch work usually isn’t — and a specific, confirmed code is exactly what an honest transmission shop wants to see.

Parts & tools you may need

Disclosure: some links are affiliate links (including the Amazon Associates program). If you buy through them, we may earn a commission at no extra cost to you.

Related codes

Frequently asked questions

What does code P0706 mean?
P0706 means the PRNDL sensor's signal exists but doesn't match reality or changes implausibly. It’s moderately serious — you can usually keep driving gently, but diagnose it soon.
Can I drive with P0706?
Usually yes for the short term, especially if shifting feels normal. If the transmission enters limp mode or starts slipping, stop driving it and diagnose — slip damage compounds fast.
Will a fluid change fix it?
If the fluid is low, burnt, or wrong-spec — quite possibly, and it’s the mandatory first step regardless. It won’t fix a genuinely failed solenoid or sensor, which is why you test those electrically before and after.
Is this code a “transmission rebuild”?
Usually not. Most codes in this family are sensors, solenoids, wiring, or fluid — hundreds, not thousands. Internal repair only enters the picture when ratio/slip codes persist after the electrical and fluid layers check out.
Why do I also have P0700?
P0700 is just the messenger: the transmission module asked the engine computer to turn on the light. Your real diagnosis is this code.
Ask Codi